Peel the protective backing off both sides of all the laser-cut parts.

You will need ODROID-VU7 package, (A), 8 x (H), 4 x (J)

Align a spacer(J) on the bottom side and a screw(H) on the top side. Insert a screw and tighten it carefully.

Keep the screw hole empty at the top middle marked with an X in the picture.

Check Step4 for the other side of the ODROID-VU7.

You need screws and spacers bundled with ODROID-VU7.

Align a spacer on the bottom side and a screw on the top side. Insert a screw and tighten it carefully

You only need to install screws at the 2 points marked with an O in the image.

Continue using the screws from the ODROID-VU7 bundle.

Add screws at the 2 points marked with an O in the image. Insert screws and tighten them gently.

Plug in the Micro USB link board and the HDMI link board.

Assemble the front piece(A) with the ODROID-VU7.

You need 4 x (H). Tighten it gently.

Don’t tighten too much or the acrylic will crack.

Assemble the front piece(A) and right side piece(C).

Align the locker on the front piece with the locking hole on the right side piece(C). Apply gentle pressure to it.

Assemble the bottom1 piece(D).

Align the locker on the bottom1 piece(D) with the locking hole on the right side piece(C).

Apply gentle pressure to it.

Assemble the bottom2 piece(E).

Align the locker on the bottom2 piece(E) with the locking hole on the right side piece(C).

Apply gentle pressure to it.

Assemble the bottom3 piece(F).

Align the locker on the bottom3 piece(F) with the locking hole on the right side piece(C).

Apply gentle pressure to it.

Assemble the left side piece(B).

Align the locker on each piece with the locking hole on the left side piece. Apply gentle pressure to it.

Align the cover piece(G) on the hole with the left side piece(B) and the right side piece(C).

Input the power source.

Pinch the edge of the each locker with two fingers. Please be careful not to crack the locker.

Peel the protective backing off both sides of all the laser-cut parts.

Align a spacer(J) on bottom side and a screw(H) on top side.

Tighten it gently.

Leave the screw hole empty at top middle marked with an X in the picture.

Assemble the front piece(A) with the ODROID-VU7.

You need 4 x (H). Tighten it gently.

Don’t tighten too much or the acrylic will crack.

Align a spacer(J) on bottom side of the ODROID-XU4 and a screw(I) on top side of ODROID-XU4.

Insert a screw and tighten it gently.

Align the screw and spacer installed ODROID-XU4 on the bottom piece(E).

Give a screw(H) a few easy turns on bottom side.

If you do not want to install the SATA drive, please skip to Step 11.

SATA Bridge Board package is not included.

The black rubber rings work as spacers.

Align the center of the black rubber ring on the screw hole of SATA drive.

Standard SATA drives have 4 screw holes.

Align the screw hole of the bottom1 piece(D) on top.

Give a few easy turn. Please make sure not to tighten it too much. The SATA Bridge board needs 1mm of space between the SATA drive and the bottom1 piece.

Plug the SATA Bridge board to SATA drive.

SATA Bridge board includes

– SATA Bridge board

– 4 x black rubber rings

– USB 3.0 Cable

Plug one side of USB3.0 cable to SATA Bridge board and the other side to USB3.0 port on ODROID-XU4.

Plug Micro-toTypeA USB Cable to USB port on the ODROID-XU4. The cable is bundled with the ODROID-VU7.

Plug TypeA-to-TypeA HDMI Cable to HDMI port on ODROID-XU4. The cable is bundled with ODROID-VU7.

Assemble the installed front piece(A) with the left side piece(B).

Align the locker on the front piece(A) with the locking hole on the left side piece(B). Hold the front piece(A) and press gently the left side piece(B) with your fingers.

Assemble the bottom1 piece(D).

Align the locker on the bottom1 piece(D) with the locking hole on the left side piece(B).

Press it with your fingers gently.

Assemble the bottom2 piece(E).

Align the locker on the bottom2 piece(E) with the locking hole on the left side piece(B).

Hold the bottom2 piece(E) and press the left side piece(B) with your fingers gently.

Assemble the bottom3 piece(F).

Align the lock on the bottom3 piece(F) with the locking hole on the left side piece(B).

Hold the bottom2 piece(F) and press the left side piece(B) with your fingers gently.

Pass through the HDMI cable and USB cable via honeycombs. Please check the right honeycomb location from the below image.

Assemble the right side piece(C).

Align each locker on each piece with the locking hole on the right side piece(C). And press it gently with your fingers.

Plug the HDMI cable to the HDMI connector on the ODROID-VU7.

Plug the microUSB cable to microUSB connector on the ODROID-VU7.

Check that the cables are plugged in correctly.

Check that all the installation is done correctly. Input the 5V/4A Power Supply through one of honeycomb openings.

Align the cover piece(G) with the hole on the left side piece(B) and the right side piece(C).